Filter
Top Products
PARTS LIST FOR “A” MODELS
TIMERS ARE FOR PUSH BUTTON MODELS DR227 THERMOSTAT (CIRCUIT BREAKER)
DR221 TIMER, 115V, 30 SECONDS (A70) SP216C MOTOR, 115V, 60 HZ (A60, A70)
DR222 TIMER, 115V, 40 SECONDS (A60) SP217C MOTOR, 208-240V, 60 HZ (A80)
DR223 TIMER, 115V, 80 SECONDS (A60H, A70H) SP217C-5 MOTOR, 220-240V, 50 HZ (A50)
DR224 TIMER, 230V, 30 SECONDS (A80, A50) CI232 SECURITY SCREW & SPECIAL ALLEN WRENCH
DR225 TIMER, 230V, 80 SECONDS (A80H, A50H) CI202 COVER, MUST SPECIFY MODEL #, PUSH
DR218 HEATING ELEMENT (A60) BUTTON OR AUTOMATIC.
DR219 HEATING ELEMENT (A70) COMPLETE WITH ACCESSORIES.
DR220 HEATING ELEMENT (A80, A50) DR239-P SENSOR COMPLETE, 110-240 VOLT
(AUTOMATIC MODELS)
SERVICE AND MAINTENANCE OF YOUR DRYER
Each component used in your dryer has been designed to provide
years of trouble free service. However, if trouble should develop, it can
normally be located by visual examination. Removal or replacement of
most parts is simple and can be done without special tools.
IF COLD AIR IS COMING FROM THE NOZZLE:
Remove the cover and check the heating element. If the element is
broken or burned out, replace it.
IF NO AIR IS COMING FROM THE NOZZLE AND HEATING ELEMENT
GLOWS:
Remove the cover and check to see that the fan revolves freely. Check
and replace motor, if required.
IF NO AIR IS COMING FROM THE NOZZLE AND HEATING ELEMENT
IS NOT IN OPERATION:
Check the thermostat. Assuming the thermostat is okay the timer or
sensor should be replaced.
IF DRYER WILL NOT SHUT OFF:
Make certain the push button returns out fully after being pushed in and
released. If button moves freely, replace the timer.
AUTOMATIC DRYERS:
Check that circuit board and sensor are clean from dust and lint
(carefully dust off). Make sure plastic window is clean on both sides.
Foam piece on window must remain intact. When replacing dryer cover,
be careful not to damage circuit board or sensor.
This dryer is activated by an infrared sensor. The dryer operates as long
as hands are below nozzle. There is a maximum 80 second running time
with a safety over-ride feature, if hands are not removed. Sensitivity is
adjustable (F
Igure 3) by CAREFULLY turning the adjustment pot located
on the sensor. Use a small flat blade screw driver. 1/3 Turn MAX. Turn
CLOCKWISE to INCREASE sensitivity, COUNTER-CLOCKWISE to
DECREASE sensitivity.
FOR ANY OTHER PROBLEM, CONTACT FACTORY FOR
ASSISTANCE.
CLEANING - DO NOT spray cleaning solvents thru dryer vents. DO
NOT use abrasive, chlorinated, or highly alkaline cleaners. DO NOT use
oil based cleaners.
SEMI-ANNUALLY remove the cover and clean all lint and dust from the
mechanism, inside of cover, and plastic window.
Clean cover with a mild soap or detergent and warm water, using a soft
THERMOSTAT
TERMINAL BLOCK
BACKPLATE
SENSOR
ADJ. POT
FAN
HEATING ELEMENT
MOTOR
WARNING:
DISCONNECT POWER BEFORE SERVICING
DESUNA LA ELECTRICIDAD ANTES DE HACER REPARACIONES
FLOOR
“A”
DO NOT MOUNT TOP
SIDE DOWN
Fi g u r e 1
3/4”
10-3/4” (273mm)
9-1/4” (235mm)
8” (203mm)
1”
(25mm)
7-1/16”
(179mm)
8-9/16”
(217mm)
3/4”
(19mm)
2-3/4”
(70mm)
1”
(25mm)
Conduit Entrance
7/8” (22mm)
Dia. Hole
Conduit Entrance
7/8” (22mm) Dia. Hole
For Surface Wiring
4 Mounting Holes
5/16” (8mm)
Dia. Hole
1-1/16”
(27mm)
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
ALL MODELS
TOP
+
-
F
i g u r e 2
Se N S it i v i ty ad j u S t M e N t
FI g u r e 3