Filter
Top Products
1. Enter the current MPIN (Master Personal Identifi-
cation Number) on the SC-001.
2. Press [B].
3. Press the number key to identify which zone to
add the panic transmitter to. Do not program the
keychain transmitter to zone 1,2,3,4. The keychain
transmitter is designed to be programmed in zone
5 for SC-001. Therefore, press [5] for SC-001.
4. Press [ ] within 8 seconds.
5. Activate the keychain transmitter by pressing one
of the buttons on the transmitter. You will hear a
long beep from the control panel, and the keychain
transmitter will now communicate to that zone.
Program the Keychain Transmitter
(4B-434) to the Security Control Panel
(SC-001)
1. Press [L], [5] when in clock mode, the display will
show “L5 Id codE”.
2. Activate the keychain transmitter within 5 seconds
by pressing any button on the transmitter. The
red LED light of the transmitter will be on when
the button is pressed. The display will return to
clock mode once the keychain transmitter has
been learned.
3. If the panic button of the keychain transmitter is
pressed, it will trigger the Emergency Dialer and
start dialing preset phone numbers (refer to
AD-1010 User’s Instruction).
Program the Keychain Transmitter
(4B-434) to the Emergency Dialer
(AD-1010)
Introduction
The Keychain Transmitter
(4B-434) conveniently fits
on any keychain. It allows
you to arm and disarm the
Security Control Panel
SC-001 and activate the
Emergency Dialer AD-1010
from a maximum distance
of approximately 100 feet
from the unit. It has a
panic button that lets you
remotely activate the siren
or dialer instantly.
Operation for Emergency Dialer
(AD-1010)
The keychain transmitter (4B-434) can be
used to control the Emergency Dialer AD-
1010. The function of buttons #1, #2, #3 are
the same as the functions as T1, T2, T3 on
the keypad of the Emergency Dialer. When
one of these buttons are pressed, the dialer will
dial the stored phone number in the one-touch
memory (T1 or T2 or T3). The panic button on
the transmitter works the same as the panic
button on the keypad of the Emergency Dialer.
It activates the dialer immediately and dials
the preset emergency phone numbers.
Refer to the User’s Instruction of the Emer-
gency Dialer AD-1010 for details.
*
Operation for Control Panel (SC-001)
To arm the system using the keychain transmitter:
There are 2 different arm options to choose from:
1. Press button #1, and the Control Panel will beep once.
The system will be armed in the Away Sequence. This sequence arms the system when
you are the last person leaving the premises. (refer to SC-100 User’s Instruction for details)
Pressing button #1 will give you the same result as pressing: MPIN, [B], [C] on the keypad.
2. Press button #2, and the Control Panel will beep once.
The system will be armed in Home Sequence. It arms the system when someone remains
in the premises. (refer to SC-100 User’s Instruction for details)
Pressing button #2 will give you the same result as pressing: MPIN, [C] on the keypad.
To disarm the system using the keychain transmitter:
When the system is armed, press button #3. The red light on the transmitter flashes and the
Control Panel beeps twice. The system is now disarmed.
To deactivate the siren using the keypad transmitter:
Press and hold button #3, the red light on the transmitter flashes and the siren is deactivated.
Warranty
If, within one year from date
of purchase, this product
should become defective
(except battery), due to
faulty workmanship or
materials, it will be repaired
or replaced, without charge.
Proof of purchase is
required.
Operation for Control Panel (SC-001)
Note: It doesn’t matter what mode you are in or even
if the system is off, once the panic button (the
large red button) is pressed, the siren comes on
instantly.
Battery
The Keychain Transmitter operates on a 12
volt alkaline battery which is installed at the
factory. There are two screws on the back of
the transmitter that hold the top and bottom
cases together.
To replace the Keychain Transmitter battery:
1. Undo the two screws on the back of the
transmitter.
The bottom case will then come off.
2. Using a small screwdriver or pen, pry out
the old battery from one end.
3. Place the new battery in position. A
diagram beside the battery well indicates
which end is positive and which is
negative.
4. Close the battery cover and reinsert two
screws.
+
-
Button 3
Button 1
Button 2
Panic Button
Skylink will not be held
liable or responsible for
any misuse or application
of this product other than
for its intended use.
KEYCHAIN TRANSMITTER
USER'S INSTRUCTIONS
(Model 4B-434)
® are registered trademarks of their respective corporations
®
CE Declaration
of Conformity
This equipment complies
with the requirements
relating to electromag-
netic compatibility,
EN 301489-3.
This equipment con-
forms to the essential
requirement of the
Directive 1999/5/EC
of the European Par-
liament and of the
Council.
CUSTOMER SERVICE
17 Sheard Avenue, Brampton,
Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
(Reply within 24 hrs)
http://www.skylinkhome.com
P/N. 101A165-001 Rev.1
US Patent. 6243000B1
©2004 SKYLINK GROUP
NOTE
If you would like to order Skylink’s
product or have difficulty getting
your Skylink’s product to work,
please :
1. visit our website FAQ at
www.skylinkhome.com, or
2. email us at
support@skylinkhome.com
(reply within 24 hrs)
3. call our toll free at
1-800-304-1187 from Monday
to Friday, 9 am to 5 pm EST.
fax 1-800-286-1320