Panasonic WV-CP240 Security Camera User Manual


 
Copper wire
size (AWG)
Copper wire
size (AWG)
Length
of Cable
(Approx.)
CONNECTIONS
A. WV-CP240 (120V AC 60Hz)
Connect the power cord to an electrical outlet
of 120V AC 60Hz.
B. WV-CP242 (12V DC)
Connect the power cord to the DC 12V IN ter-
minal on the rear panel of the WV-CP242.
Resistance of copper wire [at 20°C (68°F)]
Calculation of maximum cable length
between camera and power supply :
Resistance
/m
Resistance
/ft
#24
(0.22mm
2
)
0.078
0.026
#22
(0.33mm
2
)
0.050
0.017
#20
(0.52mm
2
)
0.03.
0.010
#18
(0.83mm
2
)
0.018
0.006
10.5V DC VA (R x 0.42 x L) 16V DC
L : Cable length (meters)
R : Resistance of copper wire (/meter)
VA : DC output voltage of power supply unit
VA 12
L standard = (meters)
0.42 x R
VA 16
L minimum = (meters)
0.42 x R
VA 10.5
L maximum = (meters)
0.42 x R
The following adjustment should be made by
qualified service personnel or system installers.
q Loosen the screw on the side of the camera.
w Turn the flange-back adjusting ring to the
desired position.
Caution: When the C-mount lens is mounted,
do not rotate the ring counterclockwise
by force after it stops. If the ring is rotat-
ed by force, the inner lens or CCD image
sensor may be damaged.
e Tighten the screw on the side of the camera.
Caution: Tightening the screw by force will
cause damage to the screw or deviation
of focus.
FOCUS OR FLANGE-BACK ADJUSTMENT
12 V DC
(10.5 V - 16 V)
@
!
C. WV-CP244 (24V AC 60Hz)
Connect the power cable to the AC 24 V IN
terminal on the rear panel of the WV-CP244.
(m)
(ft)
#24
(0.22mm
2
)
95
314
#22
(0.33mm
2
)
150
495
#20
(0.52mm
2
)
255
842
#18
(0.83mm
2
)
425
1 403
Recommended wire gauge sizes for 24 V AC line
24 V AC, 60 Hz
(19.5 V - 28 V)
1 2
Installation of Auto Iris Lens
Connector
Install the lens connector (YFE4191J100) when
using a video drive ALC lens.
The installation should be made by qualified
service personnel or system installers.
Cut the iris control cable at the edge of the lens
connector to remove the existing lens connector
and then remove the outer cable cover of the sup-
plied connector as shown in the diagram.
The pin assignment of the lens connector is as fol-
lows:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used
Pin 3: Video signal; 0.7 V[p-p]/40 k
Pin 4: Shield, ground
Pin 3
Pin 4
Pin 2
Rib
Pin 1
Mounting the Lens
Caution:
Before you mount the lens, loosen the screw
on the side of the camera, and rotate the
flange-back adjusting ring clockwise until it
stops. If the ring is not at the end, the inner
lens or CCD image sensor may be damaged.
q Mount the lens by turning it clockwise on the
lens mount of the camera.
w Connect the lens cable to the auto iris lens
connector on the side of the camera.
Focus Fixing Screw
w
q
cs
c
Caution for Mounting the Lens
The lens mount should be a C-mount or CS-mount
(1”-32UN) and the lens weight should be less than
450 g (0.99 lbs). If the lens is heavier, both the
lens and camera should be secured by using the
supporter.
The protrusion at the rear of the lens should be as
shown in the diagram.
C-mount: Less than 13 mm (1/2”)
CS-mount: Less than 8 mm (5/16”)
Solder the lens cable to the pins of the sup-
plied connector.
Flange-back
Adjusting Ring
Focus Fixing Screw
Focusing of
C-mount lens
Focusing of
CS-mount lens
LOCK
Caution:
To prevent fire or electric shock hazard, use
a UL listed cable (VW-1, style 1007) for the
DC 12 V or AC 24 V Input Terminal.
Video Cable
1. It is recommended to use a monitor whose
resolution is at least equal to that of the
camera.
2. The maximum extensible coaxial cable
length between the camera and the moni-
tor is shown below.
Type of RG-59/U RG-6U RG-11/U RG-15/U
coaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V)
Recommended (m) 250 500 600 800
maximum
cable length (ft) 825 1 650 1 980 2 640
Pick-up Device: 768 (H) x 494 (V) pixels, Interline Transfer CCD
Scanning Area: 4.92 (H) x 3.70 (V) mm (Equivalent to scanning area of 1/3”
pick-up tube)
Synchronization: Internal, Line-locked or Multiplexed vertical drive (VD2),
selectable
Scanning System: 2 : 1 interlace
Scanning: 525 lines / 60 fields / 30 frames
Horizontal: 15.734 kHz
Vertical: 59.94 Hz
Horizontal Resolution: 480 lines
Video Output: 1.0 V[p-p] NTSC composite 75 / BNC connector
Signal-to-Noise Ratio: 50 dB (Equivalent to AGC Off, weight On)
Electronic Light Control: Equivalent to continuous variable shutter speed between 1/60 s
and 1/15 000 s
Minimum Illumination: 0.6 lx (0.06 foot-candle) at F0.75 [equivalent to 2.0 lx (0.2 foot-
candle) at F1.4] AGC On
Detail: SHARP or SOFT, selectable
Lens Mount: C-mount or CS-mount, selectable
Ambient Operating Temperature: 10°C - +50°C (14°F - 122°F)
Ambient Operating Humidity: Less than 90 %
Power Source and WV-CP240: 120 V AC 60 Hz, 3.6 W
Power Consumption: WV-CP242: 12 V DC, 270 mA
WV-CP244: 24 V AC 60 Hz, 3.3 W
Dimensions (without lens): 67 mm (W) x 65 mm (H) x 123 mm (D)
2-5/8” (W) x 2-9/16” (H) x 4-13/16” (D)
Weights (without lens): WV-CP240: 0.48 k
g (1.06 lbs)
WV-CP242: 0.3 k
g (0.66 lbs)
WV-CP244: 0.33 k
g (0.73 lbs)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
SPECIFICATIONS
STANDARD ACCESSORIES
Body Cap............................................................................................1 pc.
ALC Lens Connector (YFE4191J100).................................................1 pc.
OPTIONAL ACCESSORIES
Lenses: WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3, WV-LA908C3,
WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LFY3C3,
WV-LFY45C3, WV-LFY9C3
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina,
P.R. 00985 (809)750-4300
Panasonic Digital Communications & Security Company
Unit of Matsushita Electric Corporation of America
Security Systems Group
www.panasonic.com/cctv
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Zone Office
Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205
Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
2003 © Matsushita Electric Industrial Co., Ltd. All rights reserved.
1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light
Control (ELC)
(2) Automatic Gain Control (AGC) +15 dB
and Automatic Tracing White Balance
(ATW)
(3) Camera synchronization mode selec-
table between internal (INT), Line-locked
(LL) for WV-CP240 and WV-CP244 and
Multiplexed Vertical Drive (VD2).
FEATURES
2. Minimum illumination of 0.6 lx (0.06 foot-can-
dle) at F0.75 (equivalent to 2.0 lx (0.2 foot-
candle) at F1.4)
3. Signal-to-noise ratio of 50 dB
(Equivalent to AGC Off)
4. Horizontal resolution of 480 lines
5. Auto iris lens control selectable between
video signal and DC power supply.
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove
screws or covers.
There are no user serviceable parts inside.
Ask a qualified service person for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking,
shaking, etc. The camera could be damaged
by improper handling or storage.
3. Do not expose the camera to rain or
moisture, or try to operate it in wet areas.
Turn the power off immediately and ask a
qualified service person for servicing.
Moisture can damage the camera and also
create the danger of electric shock.
4. Do not use strong or abrasive detergents
when cleaning the camera body.
Use a dry cloth to clean the camera when
dirty.
In case the dirt is hard to remove, use a mild
detergent and wipe gently. Afterwards, wipe
off the remained part of the detergent in it
with a dry cloth.
5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive
detergents. Use lens tissue or a cotton tipped
applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects.
PRECAUTIONS
Caution:
To prevent fire or electric shock hazard, use
a UL listed cable (VW-1, style 1007) for the
DC 12 V or AC 24 V Input Terminal.
Cautions:
Connect to 12 V DC (10.5 V-16 V) or 24 V
AC (19.5 V-28 V) class 2 power supply only.
Make sure to connect the grounding lead to
the GND terminal when the power is sup-
plied from a 24 V AC power source.
To prevent fire or electric shock hazard, use
a UL listed cable (VW-1, style 1007) for the
DC 12 V or AC 24 V Input Terminal.
GND
AC 24V IN
12
VIDEO OUT
VIDEO OUT
VIDEO OUT
<WV-CP240>
<WV-CP244>
<WV-CP242>
DC 12V IN
WV–
CP244
LL
INT
ELC
ALC
SOFT
SHARP
OFF
BLC ON
DC
VIDEO
ELC
ALC
SOFT
SHARP
OFF
BLC ON
DC
VIDEO
LL
INT
ELC
ALC
SOFT
SHARP
OFF
BLC ON
DC
VIDEO
LL
INT
ELC
ALC
SOFT
SHARP
OFF
BLC ON
DC
VIDEO
ELC
ALC
SOFT
SHARP
OFF
BLC ON
DC
VIDEO
LOCK
Fixing Screws
Camera Mounting
Screw Holes
Mount Adapter
cs
c
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
q Auto Iris Lens Connector
Supplies power and control signals to an auto
iris lens (not supplied).
w Flange-back Adjusting Ring
This ring adjusts the back-focal distance or
picture focus. Rotate this ring clockwise for a
C-mount lens or counterclockwise for a CS-
mount lens.
e Lens (option)
r Mount Adapter
The camera mounting screw hole is for
mounting the camera onto a mounting brack-
et. The camera is originally designed to be
mounted from the bottom, however, a top-
mounting type is also available. To mount
from the top, remove the mount adapter from
the bottom of the camera by removing two
fixing screws. Attach the mount adapter to
the top as shown in the diagram, then mount
the camera on the mounting bracket. Make
sure that two original screws are used when
mounting the mount adapter; longer type
screws may damage inner components, too
shorter type screws may cause the camera
drop.
t Focus Fixing Screw
y Power Cord (only for WV-CP240)
Connect this power cord to an electrical out-
let of 120 V AC 60 Hz.
u DC 12 V Input Terminal
[DC 12V IN (only for WV-CP242)]
This terminal is for connecting the 12 V DC
power supply cord.
i AC 24 V Input Terminal
[AC 24V IN (only for WV-CP244)]
This terminal is for connecting the 24 V AC
60Hz power supply cord.
o Synchronization Mode Selector
[INT, LL (only for WV-CP240 and WV-
CP244)]
Selects the camera synchronization mode as
either internal sync mode (INT) or line-lock
mode (LL).
INT: Sets to internal 2:1 interlace.
LL: Sets to Line-lock mode.
!0 Back Light Compensation Mode Selector
(BLC ON, OFF)
Lets you select the mode according to the
position of the object and light conditions on
the screen.
ON: Select this mode when a strong light
such as a spotlight is in the background.
OFF: Normal picture.
!1 Detail/Aperture Level Selector (SHARP,
SOFT)
The detail/aperture level can be selected with
this selector. Set it to the desired position
while observing the picture on the monitor.
SHARP: Normal position.
SOFT: Select this position when a Quad
System is connected to this camera.
!2 Automatic Light Control/Electronic Light
Control Selector (ALC, ELC)
Lets you select the mode according to the
lens type used.
ALC: Select this mode when an auto iris lens
(ALC lens) is used with this camera.
ELC: Select this mode when a fixed iris lens
or manual iris lens is used with this cam-
era.
!3 Lens Drive Signal Selector (VIDEO, DC)
Lets you select the mode according to the
type of auto iris lens drive signal to be sup-
plied to the lens from the auto iris lens con-
nector.
VIDEO: Select this mode if you are using a
auto iris lens that requires a video drive
signal.
DC: Select this mode if you are using a auto
iris lens that requires a DC drive signal.
!4 Video Output Connector (VIDEO OUT)
This connector is for connecting with the
VIDEO IN connector of the video monitor.
Whenever the multiplexed vertical drive (VD2)
signal is supplied to this connector, the cam-
era synchronization mode is automatically set
to Vertical Drive.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N0301-3043 V8QA5733DN Printed in Japan
N 19
Model No. WV-CP240
WV-CP242
WV-CP244
Color CCTV Cameras
Operating Instructions
cs
c
(Lens Option)
Whether the camera is in use or not, never
aim it at the sun or other extremely bright
objects. Otherwise, blooming or smear may
be caused.
7. Do not operate the camera beyond the
specified temperature, humidity or power
source ratings.
Use the camera under conditions where tem-
perature is between –10°C - +50°C (14°F -
122°F), and humidity is below 90 %. The
input power source is 120 V AC 60 Hz for
WV-CP240, 12 V DC for WV-CP242, and 24 V
AC 60 Hz for WV-CP244.
PREFACE
Panasonic’s WV-CP240/CP242/CP244 series digi-
tal signal processing color CCD cameras intro-
duce a new level of high picture quality and high
resolution through the use of a 1/3-inch interline
transfer CCD image sensor having 768 horizontal
pixels (picture elements), and digital signal pro-
cessing LSI’s. This model offers cutting-edge
technology for advanced video surveillance.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and mainte-
nance (servicing) instructions in the
literature accompanying the appli-
ance.
The lightning flash with arrowhead
symbol, within an equilateral trian-
gle, is intended to alert the user to
the presence of uninsulated "dan-
gerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The serial number of this product may be found on
the bottom of the unit.
You should note the serial number of this unit in the
space provided and retain this instruction as a per-
manent record of your purchase to aid identification
in the event of theft.
Model No.
Serial No.
SA 1966
SA 1965
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
VICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manu-
al, may cause harmful interference to radio com-
munications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables when
connecting to computer or peripheral devices). Any
changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate this equipment.
For U.S.A