Menu

Invacare Articulating/Elevating Legrest Mobility Aid User Manual

of 8
1
The Ratchet Replacement Kit consists of the following:
DESCRIPTION QUANTITY
Ratchet Body 2
Ratchet Bar 2
Ratchet Handle 2
Nylon Washer 2
Acorn Nut 2
Cam 2
Spring 2
Snap Ring 2
Spacer 2
Domed Push Cap 2
SAVE THESE INSTRUCTIONS
NOTE: Check ALL parts for shipping damage. In case of
shipping damage, DO NOT use. Contact Carrier/Dealer
for further instruction.
SAFETY SUMMARY
The following recommendations are made for safe
installation and adjustment of the Ratchet Replace-
ment Articulating / Elevating Legrest:
GENERAL WARNING
DO NOT install or use this kit without first read-
ing and understanding this instruction sheet.
If you are unable to understand the Warn-
ings, Cautions or Instructions, contact a
healthcare professional, dealer or technical
personnel before attempting to install this kit
- otherwise, injury or damage may occur.
DO NOT step or stand on footrests; it could
cause the chair to tip over resulting in injury.
INSTALLATION WARNING
After making adjustments and BEFORE use,
make sure all attaching hardware is securely
tightened.
Ratchet Replacement - Articulating / Elevating Legrest
Assembly, Installation and Operating Instructions
REMOVING EXISTING RATCHET
ASSEMBLY (FIGURE 1)
NOTE: Note location and orientation of ratchet assembly
BEFORE removing for installation of NEW ratchet kit.
1. Determine how the ratchet handle is secured to the
legrest.
2. Perform one (1) of the following:
If the ratchet handle is secured with a Roll Pin:
A. Use a hammer and a punch to remove the roll pin
that secures the ratchet handle to the ratchet as-
sembly as shown in FIGURE 1, DETAIL “A”.
B. Adjust the legrest assembly until the ratchet as-
sembly including handle can be removed from
the upper support tube of legrest assembly.
NOTE: When removing the ratchet assembly and handle
on the articulating legrest, open the legrest assembly until
you clear the drive link and link bar.
NOTE: This procedure will eliminate disassembling the
upper support tube from the legrest support tube and in
the case of the articulating legrest the gears will not have
to be remeshed to obtain correct travel.
C. Remove ratchet body and ratchet handle from
upper support tube as shown in FIGURE 1,
DETAIL “A”.
D. Discard the existing ratchet parts.
If the ratchet handle is secured with a snap ring:
A. Remove the snap ring from the end of the ratchet
handle using snap ring tool.
B. If equipped, remove the domed push cap that se-
cures the ratchet bar to the legrest support tube.
C. Adjust the legrest assembly until the ratchet as-
sembly including handle can be removed from
the upper support tube of the legrest assembly.
D. Remove ratchet body and ratchet handle from upper
support tube.
E. Discard the existing ratchet parts.
Have the following tools available:
Hammer
Punch
Snap Ring Tool
next

Need help with this product?


Related Invacare Products

  • 00-313 - Invacare Tarsys Series Powered Seating Systems Brochure
  • 01-349 - Invacare Solara jr. Tilt-in-SpaceWheelchair Brochure
  • 1000 - Invacare Wheelchair Assembly, Installation and Operating Instructions
  • 1034177 - Invacare Patient Operated Wheel Locks Installation, Assembly and Operating Instructions
  • 1035965 - Invacare Wheelchair Tray Assembly, Installation, and Operating Instructions
  • 1035966 - Invacare Wheelchair Tray Assembly, Installation, and Operating Instructions
  • 1036793 - Invacare Space Saver/ Conventional Arm Assembly,Installation and Operating Instructions
  • 1036794 - Invacare Space Saver/ Conventional Arm Assembly,Installation and Operating Instructions
  • 1036900 - Invacare Anti-Tippers Assembly, Installation and Operating Instructions
  • 1036901 - Invacare Anti-Tippers Assembly, Installation and Operating Instructions
  • 1038599 - Invacare Wheel Lock Extension Handle Assembly,Installation and Operating Instructionsc
  • 1048085 - Invacare Quad Cane Camlock Assembly, Installation and Operating Instructions
  • 1048086 - Invacare Quad Cane Camlock Assembly, Installation and Operating Instructions
  • 1048919 - Invacare Wheelchairs Assembly, Installation and Operating Instructions
  • 1048920 - Invacare Wheelchairs Assembly, Installation and Operating Instructions
  • 1048921 - Invacare Wheelchairs Assembly, Installation and Operating Instructions
  • 1048922 - Invacare Wheelchairs Assembly, Installation and Operating Instructions
  • 1049522 - Invacare Personal Back Headrest Reinforcement Plate Assembly,Installation and Operating Instructions
  • 1055947 - Invacare Quad Cane Camlock Assembly, Installation and Operating Instructions
  • 1055948 - Invacare Quad Cane Camlock Assembly, Installation and Operating Instructions






TRUSTe Seal


  • Facebook
  • Twitter
  • ManualsOnline Blog
  • ManualsOnline Google Plus