Conair LWD1P Electric Shaver User Manual


 
Le felicitamos por haber comprado esta
máquina de afeitar de doble hoja. Para lograr
resultados óptimos, siempre lea las instruccio-
nes de uso y mantenimiento que se encuentran
a continuación.
Gracias por elegir Conair, el
no. 1 en aparatos de cuidado personal.
GUARDE ESTAS
INSTRUCCIONES
ADVERTENCIA
1. Si su piel es sensible a los productos
cosméticos, se irrita fácilmente cuando se
afeita o padece de alergia, pruebe el aparato
sobre una pequeña sección del brazo o de la
pierna antes de usarlo.
2. Las hojas de afeitar son delgadas y
precisas. No las apriete mucho sobre la
piel ni las deje caer. Una hoja lastimada o
deformada impedirá el buen
funcionamiento del aparato y puede
provocar heridas. Reemplace las hojas
defectuosas inmediatamente.
3. Limpie las hojas en agua fría o tibia
únicamente. No utilice agua caliente, agua
salina o limpiadores, porque esto puede dañar
los sellos de impermeabilidad del aparato.
4. Enjuague el cabezal solamente. No sumerja
el aparato en agua.
5. Si use desodorante, lave bien y deje secar
las hojas y las cuchillas al aire después de
cada uso. Si no lo hace, las cuchillas se
pueden oxidar.
INSTRUCCIONES
DE OPERACIÓN
IMPORTANTE
Este aparato ha sido diseñado para
proporcionar un afeitado al ras suave y
preciso. Requiere 2 pilas AAA (no incluidas).
Le aconsejamos que utilice pilas alcalinas,
las cuales son más duraderas. Retire la(s)
pila(s) al final de su vida útil o si no va a
usar el aparato durante un largo período de
tiempo.
Durante tres a cuatro semanas, utilice
exclusivamente la máquina de afeitar para
afeitar sus piernas/axilas. Puede que sus
primeros intentos no sean perfectos. Esto es
normal. Su piel y sus vellos necesitan tiempo
para acostumbrarse a esta nueva técnica de
afeitado. Precaución: Presionar las hojas
mucho contra la piel no producirá resultados
satisfactorios. Se debe pasar la máquina
suavemente sobre la piel; presionar mucho
aplasta los vellos e impide el afeitado. Sea
paciente; utilice el aparato 10–12 veces
antes de juzgar su rendimiento.
PRECAUCIÓN:
No sumerja el aparato en agua u otro líquido.
Las hojas de afeitar y las cuchillas internas son
delicadas y deben manipularse con mucho
cuidado.
PREPARACIÓN
1. Aplique crema de afeitar o jabón sobre la
piel antes de afeitarse con agua. Esto
facilitará el afeitado y eliminará los residuos
de aceite. Precaución: NO utilice gel de
afeitar, ya que los geles pueden obstruir
las hojas.
2. Antes del afeitado en seco, asegúrese de
que su piel esté limpia. Si su piel es sensible,
puede aplicar talco antes y después del
afeitado.
3. Limpie el aparato después de cada uso.
Esto asegurará un rendimiento óptimo. Para
más información, véase la sección
"Instrucciones de limpieza".
INSTRUCCIONES DE USO
1. Para encender el aparato, ponga el
interruptor en la posición "ON".
2. Después de cada uso, apague el aparato
(OFF) y limpie el cabezal.
CÓMO AFEITAR SU AXILAS
1. Prepare la piel para el tipo de afeitado
deseado, con agua o en seco. Asegúrese de que
la piel esté limpia, seca y libre de desodorante.
2. Encienda el aparato.
3. Alce el brazo para estirar ligeramente la piel.
4. Si el vello es largo, acórtelo con la cuchilla
recortadora integrada, pasando la máquina en
dirección contraria al crecimiento del vello.
5. Mantenga el aparato en contacto con la piel y
aféitese con movimientos suaves.
6. No presione mucho. Presionar mucho puede
causar irritaciones cutáneas.
7. Después de terminar, apague el aparato
(OFF).
Importante: Necesitará hacer varios intentos
hasta encontrar la mejor forma de afeitar sus
axilas.
INSTRUCCIONES DE LIMPIEZA
1. Asegúrese de que el aparato esté apagado
(OFF).
2. Sosteniendo firmemente el cabezal, oprima
los botones de liberación y alce el cabezal
(FIG.1). Tenga cuidado de no presionar las
hojas. Son delicadas y pueden dañarse
fácilmente.
Presionar aquí
Fig. 1
Presionar aquí
CÓMO AFEITAR SUS
PIERNAS/INGLES
NOTA: Presionar las hojas contra la piel aplasta
los vellos e impide el afeitado. La experiencia le
mostrará cuanta presión aplicar para obtener
resultados óptimos.
1. Prepare la piel para el tipo de afeitado
deseado, con agua o en seco.
2. Encienda el aparato (ON).
3. Mueva la máquina suavemente contra la piel,
arriba y abajo.
4. Siempre mantenga el aparato en contacto con
la piel.
5. Para lograr resultados óptimos, aféitese en
dirección contraria al crecimiento del vello.
6. La máquina de afeitar está equipada con una
cuchilla recortadora integrada para acortar el
vello largo. Para afeitar las ingles, acorte los
vellos primero con la cuchilla recortadora
integrada.
3. Enjuague las cuchillas internas y las hojas
bajo agua corriente. No utilice agua caliente.
Utilice agua fría o tibia solamente.
4. Permita que las cuchillas y las hojas sequen
al aire antes de volver a ensamblar el cabezal.
Una vez seco, vuelva a instalar el cabezal,
presionando hasta que encaje en su lugar.
Limpie el cuerpo del aparato con una toalla
seca. No seque las hojas. Permita que sequen
al aire.
PARA USO DOMÉSTICO
SOLAMENTE
INSTRUCCIONES DE OPERACIÓN
1. Deslice la cubierta del compartimiento de
la(s) pila(s) hacia abajo para abrirlo.
2. Instale dos pilas AAA, respetando los signos
de polaridad. Introduzca el polo negativo
primero, teniendo cuidado de no doblar las
patas de contacto.
3. Cierre la cubierta del compartimiento de
la(s) pila(s), empujando hasta que haga clic.
4. Para encender el aparato, deslice el
interruptor hacia arriba (ON).
5. Para apagar el aparato, deslice el
interruptor hacia abajo (OFF).
6. Siempre respete los signos de polaridad
(+/-) al instalar la(s) pila(s).
7. Retire la(s) pila(s) al final de su vida útil o si
no va a usar el aparato durante un largo
período de tiempo.
8. Limpie los contactos del aparato y los de
la(s) pila(s) antes de instalar ésta(s).
9. Retire las pilas usadas sin demora.
10. No utilice pilas que no sean del tamaño o
de la potencia indicada para uso con este
aparato.
11. Cambie todas las pilas al mismo tiempo.
12. No junte pilas nuevas con pilas usadas.
No junte pilas alcalinas con pilas regulares
(carbón-zinc) o pilas recargables (NiCd o
NiMH).
Congratulations on the purchase of your new
ladies dual foil shaver. For maximum satisfaction
when using this quality product, please take a
minute to read the following operating and care
instructions. Thank you for choosing Conair, the
#1 brand in personal care appliances.
SAVE THESE
INSTRUCTIONS
WARNING
1. Women whose skin is sensitive to cosmetics
or easily irritated by shaving, or who suffer from
a skin allergy, should test one section of the leg
or arm before using the shaver.
2. The foils are thin and precisely finished
pieces. Do not press hard against the
foils, or drop foils. A warped or distorted
foil will produce poor shaving results.
Also a damaged foil may cause skin
injury. A damaged foil should be replaced
immediately.
3. When cleaning, use cold or warm water.
Do not use hot water, sea water, or cleaners,
as they can cause damage to the waterproof
seals.
4. Rinse the shaver head only, do not
submerge the entire unit in water.
5. To prevent possible damage to the foils and
the cutter, women who use underarm deodorant
must thoroughly clean and air-dry the foil and
cutter after each use. Failure to do this may
result in corrosion of the inner blades.
OPERATING
INSTRUCTIONS
IMPORTANT
This shaver has been engineered to give you
a clean, close, smooth shave. It requires 2
AAA batteries (not included). We recommend
using longer lasting alkaline batteries in your
shaver. If you are not going to use your
shaver for a long period of time or if the
batteries are dead, remove or replace the
batteries from the unit.
Use your shaver exclusively for three to four
weeks so that your legs and underarms
adjust to the shaver. At first, your shave
might not be as close as you expect.
However, this is normal. It takes time for your
skin and hair to adjust to the new procedure
and for you to learn how the effectively use
the shaver. Caution: Most blade users will
push too hard and therefore not get a
satisfactory shave. You must press gently so
the hair can get into the holes of the foil
pressing too hard makes the hair flat. Please
be patient; use your shaver 10 to 12 times
before you judge its performance.
12. Do not mix old and new batteries. Do not
mix alkaline, standard (Carbon-Zinc), or
rechargeable (Nickel cadmium or Nickel
Metal Hydride) batteries.
CAUTION
Do not immerse any part of the unit in water or
other liquid.
The outer foils and inner blades are delicate
and must be handled very carefully.
BEFORE SHAVING
1. Before wet shaving, you may wish to
prepare your legs and underarms with
shaving cream or soap. If a soapy lather is
applied to the skin, the shaver will glide
smoothly over the skin and clean away oil
residue while at the same time removing
hair. Caution: DO NOT use shaving gels, as
these products can clog your shaver foils.
2. When dry shaving, be certain that your
skin is clean. If you have sensitive skin, you
may want to apply talcum powder before and
after you shave.
3. Clean your shaver after each use. This will
insure the best performance. (Please refer to
“How to Clean Your Shaver” section for
further instructions.)
INSTRUCTIONS FOR USE
1. Slide the main switch up to the ON position.
2. After each shave, switch the unit off and clean
shaver head.
SHAVING YOUR UNDERARMS
1. Prepare your underarms for wet or dry
shaving. (Be sure that your skin is clean and
free of deodorant).
2. Turn the shaver on.
3. Lift your arm until the skin under the arm
stretches slightly.
4. Use the trimmer portion first to remove any
long hair, stroking trimmer against the direction
of hair growth.
5. Hold the shaver so that it is in full contact
with your skin, and shave with gentle strokes.
6. It is important to press lightly. Pressing too
hard may lead to skin irritation.
7. When finished shaving, turn the shaver off.
Important: After several uses, you will be able
to determine the optimum shaving method for
your underarms.
HOW TO CLEAN YOUR SHAVER
1. Make sure unit is in the “OFF” position
before cleaning your shaver.
2. Hold shaver head and lift up from the back,
(FIG.1) then press foil frame release buttons on
each side and lift up (the cutter is now in view).
Be careful not to push on the foils. They are
delicate and can easily be damaged.
Press Here
figure 1
Press Here
SHAVING YOUR LEGS/BIKINI AREA
NOTE: Pushing the shaver against the skin too
hard will not allow the hairs to enter the foils and
be cut. Experience will show just the right
pressing to use to maximize performance.
1. Prepare your legs for wet or dry shaving.
2. Turn shaver on.
3. Shave with smooth, steady strokes up and
down your skin.
4. Keep the full shaving head in contact with
your skin.
5. For best results, shave against the direction of
hair growth.
6. The shaver has a bikini pop-up trimmer for
your complete shaving needs. To trim the bikini
area, use the handy pop-up feature to easily see
what you are trimming.
7. When you finish shaving, turn the shaver off.
Important: After several uses, you will be able to
determine the optimum shaving method for your
legs and bikini area.
3. Rinse the shaver cutter and foil frame under
running water or in a sink. Do not use hot water.
Use only warm or cold water.
4. After wet cleaning, allow the foil frame and
cutters to air-dry before closing foil frame and
shaver head. Replace shaver head back onto the
shaver until it clicks into place. Wipe the surface
of the main unit with a dry towel. Do not dry the
foil area. Let the shaving head air-dry.
5. The cutter can also be cleaned with a
cleaning brush.
FOR HOUSEHOLD
USE ONLY
OPERATING INSTRUCTIONS
1. Remove the battery compartment cover by
pushing in and down toward the bottom of the
shaver.
2. Align the two AAA batteries with the positive
and negative positions indicated inside the
battery compartment. Being careful not to
bend the clips, insert the negative end of each
battery first so it will slip easily into place.
3. Return the battery cover to its original
position by pushing it in and up until you hear
a small click as it locks into place.
4. To use your shaver, push ON/OFF switch
upwards to ON position.
5. After you finish using your shaver, push
down on the ON/OFF switch to turn the
shaver off.
6. Ensure the batteries are installed correctly
with regard to polarity (+ and -).
7. Remove the batteries if the batteries are no
longer functional or if the shaver is left
unused for an extended period of time.
8. Clean the battery contacts and also those
of the device prior to battery installation.
9. Remove used batteries promptly.
10. Always purchase the correct size and
grade of battery most suitable for the
intended use.
11. Replace all batteries of a set at the same
time.
7. Después de terminar, apague el aparato (OFF).
Importante: Necesitará hacer varios intentos
hasta encontrar la mejor forma de afeitar sus
piernas/ingles.