Conair GMT7CS Electric Shaver User Manual


 
SAVE THESE
INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
OPERATING INSTRUCTIONS
1. Remove the battery compartment cover by
pushing in and down toward the bottom of the
trimmer.
2. Align the two AA batteries with the positive
and negative positions indicated inside the bat-
tery compartment. Being careful not to bend the
clips, insert the negative end of each battery first
so it will slip easily into position.
3. Return the battery cover to its original position
by pushing it in and up until you hear a small
click as it locks into place.
4. To use your trimmer, push ON/OFF switch
upwards to ON position.
5. After you finish using your trimmer,
push down on the ON/OFF switch to turn the
trimmer off.
6. Always purchase the correct size and grade
of battery most suitable for the intended use.
7. Replace all batteries of a set at the same
time.
8. Clean the battery contacts and also those of
the devise prior to battery installation.
9. Ensure the batteries are installed correctly
with regard to polarity (+ and -).
10. Remove batteries from equipment, which is
not to be used for an extended period of time.
11. Remove used batteries promptly.
12. Do not mix old and new batteries.
13. Do not mix alkaline, standard (Carbon-
Zinc), or rechargeable (Nickel cadmium or
Nickel Metal Hydride) batteries.
14. Store unused batteries in their original
packaging, away from metal objects that
could short-circuit them. Never short-circuit
batteries.
15. Never dispose of batteries in fire, except
under conditions of controlled incineration.
Failure to observe this precaution may result
in an explosion. Never attempt to recharge
primary batteries as this may cause leakage,
fire, or explosion.
USER MAINTENANCE
INSTRUCTIONS
TAKING CARE OF YOUR TRIMMER
OILING THE BLADES
About once a month you should oil the trim-
mer blade. It is best to do this over a piece of
newspaper. Turn the trimmer on and hold it so
that the blades are pointed downward. Spread
one drop of oil across the blades, then turn
the trimmer off and wipe away the excess oil
with a soft cloth.
Be careful not to use too much oil and don’t
oil your trimmer more than necessary, as this
could damage the motor. (Never attempt to oil
the motor bearing, as it is permanently lubri-
cated.) KEEP OIL OUT OF REACH OF CHILDREN.
ON/OFF SWITCH
To operate, simply push slide toward blade; to
stop, push slide away from blade.
*Requires 2 AA batteries (not included). We recommend
using alkaline batteries in your trimmer because they
last longer.
BLADE CARE
Because the trimmer blades are precision-made
for a very special use, they should always be
handled with care. Each time you finish using
the trimmer, take a cleaning brush and brush
away any loose hair that has collected in the
blades. Then store the trimmer to protect the
blades until the next use.
Be especially careful when changing or
adjusting blades. When you have your
trimmer serviced, be sure that both blades
are sharpened or replaced at the same time.
To promote the long life of the appliance, use
your trimmer only for the purpose intended
by the manufacturer – to trim your beard
and mustache.
REMOVING BLADE SET
This trimmer comes with a detachable
blade set; which makes maintenance easy.
To remove the blade set:
• Make sure the trimmer is in the off position
• With the power switch facing you, press the
blade on the teeth and in direction away from
you until they pop out of the housing
TO REPLACE THE BLADE SET
• Looking at the trimmer from above you will
see a notch at the back of the trimmer.
• There is a tab on the blade set on the bottom,
opposite the blades
Position that tab so that it fits into the notch
inside the trimmer head
Push the blade set down onto the trimmer
head until it snaps into place.
GROWING A BEARD AND MUSTACHE
There are three key factors that will determine
which beard or mustache style is best for you:
1. The shape and dimensions of your face.
2. The natural growth of your beard/mustache.
3. The thickness of your beard/mustache. If
you are unsure about the type of beard or
mustache that would most suit your face,
speak with a professional hair stylist and ask
for an opinion on what style would be best.
Once your beard or mustache has been styled,
it is essential that you maintain its appear-
ance. To do this, use your trimmer to trim your
beard/mustache weekly.
For the best trimming results, your beard
should be slightly damp (NOT WET) when
using your trimmer. This will prevent the trim-
mer from removing more hair than desired.
TYPES OF BEARDS/MUSTACHES
GETTING STARTED:
OUTLINING YOUR BEARD
1. It is always best to
begin with a clean, slightly
damp beard.
2. After you have combed through your beard
in the direction it grows naturally, you will
want to outline the desired shape, beginning
under your jawline.
3. Begin defining your beard’s shape under
your chin and work upward on each side
of your face toward your ears. Then define
the upper outline of your beard across your
cheeks, past your sideburns, and toward your
hairline.
NOW YOU’RE READY TO TRIM
YOUR BEARD
1. Your trimmer adjusts to five positions so you
can have a beard length from 1/8" (shortest)
to 5/8" (longest).
2. To use the 5-position comb, slide the unit
over the trimmer blades and snap it down into
position. At first, until you become familiar with
the adjustments, use the longest trim setting
(5/8"). (You can always go back and make
your beard a little shorter.)
3. Begin trimming your
beard using smooth,
even strokes. Start with
your sideburns and work
downward toward your
chin. (Never attempt to trim against the natural
growth of your beard because the hair will be
cut too short.)
4. If you decide you want a closer trim, you
can now adjust the 5-position comb attach-
ment to a shorter setting (such as 1/2" or
3/8") and go over your beard again until you
achieve the desired length.
BLENDING THE JAWLINE
1. The three jawline attachments will help
you to achieve a neat, finished trim under
your chin. To use one of the attachments,
press it down over the trimmer blades until it
clicks into position.
2. Hold the trimmer in an upright position
and begin trimming under your jawline, using
short, even strokes.
3. After your beard is blended, turn off the
trimmer and remove the attachment by
gently pulling up on tab.
TO TRIM YOUR MUSTACHE
1. For best results, start
with a clean, slightly damp
mustache.
2. Comb through your
mustache in the direction
it grows.
3. Place the 5-position comb over the trimmer
blades and snap it into position. It is a good idea
to start with the longest trim setting adjustment.
(You can always go back and cut your mustache
more closely with a shorter setting.)
ALWAYS TRIM YOUR MUSTACHE
FROM THE TOP DOWN
4. After your mustache
has been trimmed to the
desired length, remove
the 5-position comb and,
using the blades only,
define the outline of the bottom of
your mustache.
Battery Position
On/Off Switch
GUARDE ESTAS
INSTRUCCIONES
PARA USO DOMÉSTICO
SOLAMENTE
INSTRUCCIONES DE OPERACIÓN
1. Deslice la cubierta del compartimiento de la(s)
pila(s) hacia abajo para abrirlo.
2. Instale dos pilas AA, respetando los signos de
polaridad. Introduzca el polo negativo primero,
teniendo cuidado de no doblar las patas de
contacto.
3. Cierre la cubierta del compartimiento de la(s)
pila(s), empujando hasta que haga clic.
4. Para encender el aparato, deslice el interrup-
tor hacia arriba (ON).
5. Para apagar el aparato, deslice el interruptor
hacia abajo (OFF).
6. No utilice pilas que no sean del tamaño o de
la potencia indicada para uso con este aparato.
7. Cambie todas las pilas al mismo tiempo.
8. Limpie los contactos del aparato y los de la(s)
pila(s) antes de instalar ésta(s).
9. Siempre respete los signos de polaridad (+/-)
al instalar la(s) pila(s).
10. Retire las pilas si no va a usar el aparato
durante un largo período de tiempo.
11. Retire las pilas usadas sin demora.
12. No junte pilas nuevas con pilas usadas.
13. No junte pilas alcalinas con pilas regulares
(carbón-zinc) o pilas recargables (NiCd o NiMH).
14. Guarde las pilas nuevas en su paquete
original, lejos de los objetos de metal los cuales
podrían provocar un cortocircuito. Nunca corto-
circuite las pilas.
15. Nunca tire las pilas al fuego, excepto medi-
ante incineración controlada. Esto podría causar
una explosión. Nunca intente cargar una pila no
recargable. Esto podría presentar un riesgo de
pérdida de electrolito, incendio o explosión.
INSTRUCCIONES DE
MANTENIMIENTO
MANTENIMIENTO DE
SU RECORTADORA
LUBRICACIÓN
Lubrique las cuchillas aproximadamente
una vez al mes. Para no ensuciar, haga esto
encima de un periódico. Sostenga el aparato
al revés y enciéndalo. Coloque una gota de
aceite sobre las cuchillas, apague el aparato y
limpie el exceso de aceite con un paño suave.
No use demasiado aceite y no lubrique el
aparato más de lo necesario. Esto podría
dañar el motor. Tampoco no intente lubricar
las piezas del motor, las cuales son lubricadas
de por vida. MANTENGA EL ACEITE FUERA
DEL ALCANCE DE LOS NIÑOS.
BOTÓN DE ENCENDIDO/APAGADO
Para encender el aparato, deslice el botón de
encendido/apagado hacia las cuchillas. Para
apagarlo, deslícelo hacia atrás.
*Requiere 2 pilas AA (no incluidas) Le aconsejamos que
utilice pilas alcalinas, las cuales son más duraderas.
LIMPIEZA DE LAS CUCHILLAS
Las cuchillas de su aparato fueron diseñadas
con precisión para un uso específico, y deben
recibir un cuidado muy especial. Limpie las
cuchillas después de cada uso con el cepillo
de limpieza provisto. Guarde el aparato hasta el
próximo uso para proteger las cuchillas.
Tenga cuidado cuando sea necesario cambiar o
ajustar las cuchillas. Asegúrese de que ambas
cuchillas siempre estén cambiadas o afiladas al
mismo tiempo.
Para seguir disfrutando de su aparato durante
mucho tiempo, utilícelo únicamente con el
propósito para el cual fue diseñado: cortar la
barba y el bigote.
REMOCIÓN DE LAS CUCHILLAS
Su cortadora está equipada con cuchillas
extraíbles, para facilitar el mantenimiento, la
limpieza, y el reemplazo de las mismas.
Remoción:
• Asegúrese de que el aparato esté apagado.
• Sostenga el aparato con el interruptor
adelante y empuje las cuchillas hacia arriba
para desencajarlas.
INSTALACIÓN
• Si observa el aparato desde arriba, verá una
hendidura en la parte posterior.
• Hay una lengüeta en la parte inferior del
juego de cuchillas.
Introduzca la lengüeta en la hendidura.
Enganche el juego de cuchillas en su lugar
hasta que calce emitiendo un chasquido.
BARBAS Y BIGOTES
El tipo de barba o de bigote que más conviene
a una persona depende de:
1. La forma y el tamaño de su rostro.
2. La forma del crecimiento natural de su
barba o de su bigote.
3. El espesor de su barba o de su bigote. Si no
está seguro del tipo de barba o bigote que le
conviene, pida consejo a un barbero. Después
de dar forma a su barba o a su bigote, deberá
mantener su aspecto, usando la cortadora una
vez por semana.
Para lograr resultados óptimos, humedezca
ligeramente su barba antes de recortarla (no la
moje). Esto evitará cortar demasiado pelo.
TIPOS DE BARBAS Y BIGOTES
CÓMO CORTAR SU BARBA
EL CONTORNEO
1. Se le hará más fácil cor-
tar la barba si está limpia y
ligeramente humedecida.
2. Peine la barba en la dirección del creci-
miento natural del pelo antes de empezar a
darle forma.
3. Dé forma a su barba empezando debajo de
la quijada y subiendo hacia la oreja, en cada
lado del rostro. Siga dando forma al área de la
mejilla, a las patillas y a la línea de nacimiento
del cabello.
EL RECORTE
1. Su cortadora incluye una guía ajustable con
5 posiciones que corta el pelo de 3 mm (1/8
pulgada) a 16 mm (5/8 pulgada).
2. Instale la guía encima de la cuchilla de
corte. Le recomendamos que utilice el ajuste
más largo (16 mm) para empezar. Siempre
podrá volver a acortar la barba.
3. Empiece a cortar su
barba con movimientos
parejos y suaves, desde
las patillas hasta la
quijada. Nunca corte en
dirección contraria al crecimiento natural del
pelo. El recorte resultaría demasiado corto.
4. Si desea un recorte aún más corto, escoja
un largo de recorte más corto, como 9.5 mm
(3/8 pulgada) o 12.5 mm (1/2 pulgada), y siga
acortando su barba hasta conseguir el tamaño
deseado.
IGUALAR LA QUIJADA
1. Las guías para la quijada le permitirán
lograr un recorte neto y preciso. Instale la
guía encima de la cuchilla de acabado.
2. Sostenga la cortadora recta y corte el pelo
usando pequeños movimientos uniformes.
3. Después de terminar, apague el aparato y
retire el accesorio.
CÓMO CORTAR SU BIGOTE
1. Se le hará más fácil cor-
tar su bigote si está limpio
y ligeramente humedecido.
2. Peine su bigote en la
dirección del crecimiento
natural del pelo.
3. Instale la guía ajustable sobre las cuchillas.
Empiece con la posición más larga (siempre
podrá volver a acortar el bigote).
SIEMPRE CORTE SU BIGOTE
DESDE ARRIBA HASTA ABAJO
4. Después de terminar,
retire la guía y dé forma
a la parte inferior de su
bigote.
Compartimiento de las pilas
Botón de encendido/apagado